4.6 (213) · ⏠27.99 · En Stock
Ce vif dâor est composĂ© de trois piĂšces : le corps/sphĂšre, lâaile droite et lâaile gauche en symĂ©trie. ParamĂštres dâimpression : SphĂšre : - MatĂ©riaux : ABS (pour lissage Ă lâacĂ©tone) - Ăpaisseur de couche : 0,12 mm - Remplissage : 20 % - Coques de contour/pĂ©rimĂštre : 3 (Pour un bon Ă©tat de surface aprĂšs lissage Ă lâacĂ©tone) - GĂ©nĂ©rer une faible zone de support sous le vif dâor pour une bonne impression. Ailes : - MatĂ©riaux : ABS - DiamĂštre Buse : max 0.4 mm (Modifier le paramĂštre « largeur dâextrusion » (max 0,4 mm) si les accroches des plumes ne sâimpriment pas) - Ăpaisseur de couche : 0,2 mm - Remplissage : 100 % -------------------------------------------------------------------------------------- Post traitement : SphĂšre : - Enlever les supports, Ă©bavurer si nĂ©cessaire - Mettre en Ă©tuve pour lisser les surfaces extĂ©rieures - Poncer lĂ©gĂšrement sâil reste des zones non lisses - Peindre la sphĂšre du vif dâor. Jâai utilisĂ© de la peinture or en aĂ©rosol. Ailes : - Ebavurer si nĂ©cessaire - Poncer lĂ©gĂšrement les deux cotĂ©s - Faire chauffer la structure avant au sĂšche-cheveux pour lui donner la courbure dĂ©sirĂ©e. - Peindre les ailes Enfin, assembler et coller les deux ailes sur la sphĂšre dans les trous prĂ©vus Ă cette effet. Percer les trous au bon diamĂštre si nĂ©cessaire. ___________________________________________________ This snitch is made up of three parts: the body / sphere, the right wing and the left wing in symmetry. Print settings : Sphere: - Materials: ABS (for acetone smoothing) - Layer thickness: 0.12mm - Filling: 20% - Contour / perimeter shells: 3 (For a good surface condition after smoothing with acetone) - Generate a small area of support under the snitch for a good impression. Wings: - Materials: ABS - Nozzle diameter: max 0.4 mm (Modify the extrusion width parameter (max 0.4 mm) if the feather grips do not print) - Layer thickness: 0.2 mm - Filling: 100% -------------------------------------------------------------------------------------- Post-processing Sphere: - Remove the supports, deburr if necessary - Put in an oven to smooth the exterior surfaces - Lightly sand if there are non-smooth areas - Paint the golden snake sphere. I used gold spray paint. Wings: - Deburr if necessary - Lightly sand both sides - Heat the front structure with the hair dryer to give it the desired curvature. - Paint wings Finally, assemble and glue the two wings on the sphere in the holes provided for this purpose. Drill the holes to the correct diameter if necessary.
Fichier STL gratuit magicien harry potter đ§ă»ModĂšle imprimable en 3D Ă tĂ©lĂ©chargeră»Cults
Fichier STL ELFE DOBBY DE HARRY POTTER đă»Objet pour imprimante 3D Ă tĂ©lĂ©chargeră»Cults
Fichier STL gratuit Vif d'or - Harry Potter â¶ïžă»Objet imprimable en 3D Ă tĂ©lĂ©chargeră»Cults
fichier stl harry potter 3D Models to Print - yeggi
fichier stl harry potter 3D Models to Print - yeggi
â· le vif d or 3d models ă STLFinder ă
Fichier STL Harry Potter - Vif d'or - Golden snitch đšă»Design imprimable en 3D Ă tĂ©lĂ©chargeră»Cults
Fichier STL Le Vif d'or đ€ă»Design Ă tĂ©lĂ©charger et Ă imprimer en 3Dă»Cults
Fichier STL ELFE DOBBY DE HARRY POTTER đă»Objet pour imprimante 3D Ă tĂ©lĂ©chargeră»Cults
fichier stl harry potter 3D Models to Print - yeggi
fichier stl harry potter 3D Models to Print - yeggi