Lithium Ion Battery - 3.7V 2000mAh : ID 2011 : $12.50 : Adafruit
4.6 (81) · € 6.50 · En Stock
Adafruit Industries, Unique & fun DIY electronics and kits Lithium Ion Battery - 3.7V 2000mAh : ID 2011 - Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2000mAh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteriesThe batteries come pre-attached with
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2000mAh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteriesThe batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable won't snag or get stuck in a matching JST jack, they click in and out smoothly.The included protection circuitry keeps the battery voltage from going too high (over-charging) or low (over-use) which means that the battery will cut out when completely dead at 3.0V. It will also protect against output shorts. However, even with this protection, it is very important that you only use a LiIon/LiPoly constant-voltage/constant-current charger to recharge them and at a rate of 2A or less (500mA is best). We suggest our Micro Lipo charger, which has a 100mA default rate. You can also set the Micro Lipo to 500mA rate for a faster charge.Like most lipos, the batteries we sell do not have thermistors built-in. This is why we suggest charging at 1 C or even less - 100 to 500mA is a good rate, and available from any USB port if using a USB-powered chargerAdditional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, do not abuse these batteries, do not short, bend, crush, or puncture. Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or the possibility of short circuits. Polarity matches all Adafruit LiPoly/LiIon chargers and boards, other brands may have reverse polarity and can destroy your battery. As with all Lithium-ion polymer batteries and with any power source - they should be used by experts who are comfortable working with power supplies.
Lithium Ion Battery Pack - 3.7V 4400mAh : ID 354 : $19.95 : Adafruit Industries, Unique & fun DIY electronics and kits
9V battery clip with 5.5mm/2.1mm plug : ID 80 : $2.95 : Adafruit Industries, Unique & fun DIY electronics and kits
Design of a low-cost wireless NIRS system withembedded Linux and a smartphone interface
2011 Adafruit Industries LLC, Battery Products
Products – Tagged Batteries
Watch_Dogs 2 Working Wrench Cosplay Mask (bluetooth Controlled) : 10 Steps (with Pictures) - Instructables
ds18b20 Temp Sensors giving bad readings when arduino is running off battery - Sensors - Arduino Forum
Lithium Ion Polymer Battery - 3.7v 1200mAh : ID 258 : $9.95 : Adafruit Industries, Unique & fun DIY electronics and kits
备件清单607_厦门纪扬科技有限公司
Lithium Ion Polymer Battery - 3.7v 2500mAh : ID 328 : $14.95 : Adafruit Industries, Unique & fun DIY electronics and kits
3.7 V Lithium-Ion Battery Rechargeable (Secondary) 2Ah
2011
Adafruit Micro LiPo w/MicroUSB Jack - USB LiIon/LiPoly Charger
Lithium Ion Battery - 3.7V 2000mAh : ID 2011 : $12.50 : Adafruit Industries, Unique & fun DIY electronics and kits
Lithium Ion Polymer Battery - 3.7v 1200mAh : ID 258 : $9.95 : Adafruit Industries, Unique & fun DIY electronics and kits
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to
Lithium Ion Polymer Battery - 3.7v 100mAh
